FU-ES EchoSense Instruction Manual
  • ⚠Safety Instructions
  • This instruction manual version is v1.0
    • Manual Update Log
  • Measurement principle and usage scenario
    • Firmware Update Date and Version Feature Description
  • Warranty
  • Exterior, Specs, Model
  • Installation and Setup
    • Mechanism Installation
    • Mechanical and Electrical iInstallation
    • Parameter setup
      • Z02 Automatic Pipe Size Detection Guide
  • Human Machine Interface
    • Introduction of human machine interface
    • Hybrid Page Setup and Usage Interface Guide
    • Monitoring Screen
    • Simulation Mode
    • Data interpretation on monitoring screens
    • Password input page
    • Setup screen
  • Communication
    • OCT output
    • Analog current output (0-20mA, 4-20mA)
    • RS485 and Modbus RTU Setting
    • Modbus RTU Protocol
      • Read-only memory read instruction(04) and memory lists
      • Read-Write Memory List
      • Read/Write Memory Read Command (03)
      • Read-write memory single Register write instruction(06)
      • Read/Write Memory Dual-Register Write Command (30)
      • Read/Write Memory Four-Register Write Command (31)
      • Single Bit Data Read/Write Commands (01/05) (Commonly Used in HMIs)
  • Parameters Table
    • Z Category Options and Descriptions
    • A Category Options and Descriptions
      • A02 Preset Pipe Specification Table for Different Models
      • A03 ~ A07 Data Range Explanation Based on Model Specifications
    • B Category Options and Descriptions
    • K Category Options and Descriptions
    • C Category Options and Descriptions
    • D Category Options and Descriptions
    • E Category Options and Descriptions
    • F Category Options and Descriptions
    • H Category Options and Descriptions
    • Pagasfsae 1
    • Page 1
  • Alarm and description of system conditions
  • Troubleshootings and Abnormalities
    • Iout 4-20/0-20mA debug process
    • OCT Alarm Debug Process
    • OCT Pulse Debug Process
    • RS485 Debug Process
  • Certification
  • FU-ES Product Page
  • LORRIC English Website
  • LORRIC Integration and Application Center
Powered by GitBook
On this page
  • Z02 Auto Pipe Spec – Automatic Pipe Specification Detection
  • Z03 Auto Initialization – Automatic System Initialization
  • Z04 Auto Zero Offset – Automatic Zero-Flow Calibration
  • Z05 Scale Factor – Flow Scaling Factor Setting
Export as PDF
  1. Parameters Table

Z Category Options and Descriptions

PreviousParameters TableNextA Category Options and Descriptions

Last updated 3 months ago

The Z category lists the most frequently used functions from other categories in sequence, allowing users to adjust the device more conveniently.

Z02 Auto Pipe Spec – Automatic Pipe Specification Detection

This function automatically detects the pipeline specifications and, upon completion, switches to A02 to display the results. It is identical to A01. Utilising patented technology, the system senses the pipe dimensions and selects the closest matching specification. If the pipeline size has deformed or is not found in the database, a default pipeline specification will be used.

Z03 Auto Initialization – Automatic System Initialization

Activating this function allows the flow meter to adjust its signal state according to environmental conditions. This function should be executed after every reinstallation. It is identical to A21.

Ensure the pipe is completely filled with liquid before executing this function. Pay attention to the installation position—

Z04 Auto Zero Offset – Automatic Zero-Flow Calibration

Ensure the pipeline is stationary and fully filled with liquid before executing this function to correct zero-flow errors. This function is identical to A22.

Z05 Scale Factor – Flow Scaling Factor Setting

Multiplies the measured flow data by a fixed ratio, adjustable from 0.001 to 1000. To configure negative flow measurement, refer to A17. This setting is synchronised with K03.

refer to the mechanical installation section for details.
Refer to A02 for further details.