FU-ES EchoSense Instruction Manual
  • ⚠Safety Instructions
  • This instruction manual version is v1.0
    • Manual Update Log
  • Measurement principle and usage scenario
    • Firmware Update Date and Version Feature Description
  • Warranty
  • Exterior, Specs, Model
  • Installation and Setup
    • Mechanism Installation
    • Mechanical and Electrical iInstallation
    • Parameter setup
      • Z02 Automatic Pipe Size Detection Guide
  • Human Machine Interface
    • Introduction of human machine interface
    • Hybrid Page Setup and Usage Interface Guide
    • Monitoring Screen
    • Simulation Mode
    • Data interpretation on monitoring screens
    • Password input page
    • Setup screen
  • Communication
    • OCT output
    • Analog current output (0-20mA, 4-20mA)
    • RS485 and Modbus RTU Setting
    • Modbus RTU Protocol
      • Read-only memory read instruction(04) and memory lists
      • Read-Write Memory List
      • Read/Write Memory Read Command (03)
      • Read-write memory single Register write instruction(06)
      • Read/Write Memory Dual-Register Write Command (30)
      • Read/Write Memory Four-Register Write Command (31)
      • Single Bit Data Read/Write Commands (01/05) (Commonly Used in HMIs)
  • Parameters Table
    • Z Category Options and Descriptions
    • A Category Options and Descriptions
      • A02 Preset Pipe Specification Table for Different Models
      • A03 ~ A07 Data Range Explanation Based on Model Specifications
    • B Category Options and Descriptions
    • K Category Options and Descriptions
    • C Category Options and Descriptions
    • D Category Options and Descriptions
    • E Category Options and Descriptions
    • F Category Options and Descriptions
    • H Category Options and Descriptions
    • Pagasfsae 1
    • Page 1
  • Alarm and description of system conditions
  • Troubleshootings and Abnormalities
    • Iout 4-20/0-20mA debug process
    • OCT Alarm Debug Process
    • OCT Pulse Debug Process
    • RS485 Debug Process
  • Certification
  • FU-ES Product Page
  • LORRIC English Website
  • LORRIC Integration and Application Center
Powered by GitBook
On this page
  • C01 Total Method
  • C02 Del. Total (Delete Total)
  • C03 Dosing Mode
  • C04 Dosing Target
  • C05 Dosing Timer
Export as PDF
  1. Parameters Table

C Category Options and Descriptions

C01 Total Method

Defines the method for calculating the cumulative flow. Options include:

  • Positive Flow

  • Negative Flow

  • Net Flow

Changing this method will reset the cumulative flow data. Default setting: Positive Flow.

Option
RS-485 Numbers
Remarks

POS

0

Default

NET

1

NEG

2

After selecting a command, confirm whether to Save or Not Save.

C02 Del. Total (Delete Total)

Clears the cumulative flow data. Selecting this option will reset all cumulative flow values to zero.

Option
RS-485 Numbers
Remarks

No

0

Yes

1

After selecting a command, confirm whether to Save or Not Save.

C03 Dosing Mode

Manually adjusts the dosing mode to either Count Up (incremental) or Count Down (decremental). Default setting: Off.

Option
RS-485 Numbers
Remarks

OFF

0

Count Up

1

Default

Count Down

2

After selecting a command, confirm whether to Save or Not Save.

C04 Dosing Target

Sets the target value for dosing operations. Default value: 1000.

Parameter Input Range
Values

Data Type

float32

Default

1000

Minimum

0.1

Maximum

999,999,999

After selecting a command, confirm whether to Save or Not Save.

C05 Dosing Timer

Resets the dosing timer. Minimum value: 1 second. Default value: 300 seconds.

Parameter Input Range
Values

Data Type

int

Default

300

Minimum

1

Maximum

3600

After selecting a command, confirm whether to Save or Not Save.

PreviousK Category Options and DescriptionsNextD Category Options and Descriptions

Last updated 4 months ago