FU-ES EchoSense Instruction Manual
  • ⚠Safety Instructions
  • This instruction manual version is v1.0
    • Manual Update Log
  • Measurement principle and usage scenario
    • Firmware Update Date and Version Feature Description
  • Warranty
  • Exterior, Specs, Model
  • Installation and Setup
    • Mechanism Installation
    • Mechanical and Electrical iInstallation
    • Parameter setup
      • Z02 Automatic Pipe Size Detection Guide
  • Human Machine Interface
    • Introduction of human machine interface
    • Hybrid Page Setup and Usage Interface Guide
    • Monitoring Screen
    • Simulation Mode
    • Data interpretation on monitoring screens
    • Password input page
    • Setup screen
  • Communication
    • OCT output
    • Analog current output (0-20mA, 4-20mA)
    • RS485 and Modbus RTU Setting
    • Modbus RTU Protocol
      • Read-only memory read instruction(04) and memory lists
      • Read-Write Memory List
      • Read/Write Memory Read Command (03)
      • Read-write memory single Register write instruction(06)
      • Read/Write Memory Dual-Register Write Command (30)
      • Read/Write Memory Four-Register Write Command (31)
      • Single Bit Data Read/Write Commands (01/05) (Commonly Used in HMIs)
  • Parameters Table
    • Z Category Options and Descriptions
    • A Category Options and Descriptions
      • A02 Preset Pipe Specification Table for Different Models
      • A03 ~ A07 Data Range Explanation Based on Model Specifications
    • B Category Options and Descriptions
    • K Category Options and Descriptions
    • C Category Options and Descriptions
    • D Category Options and Descriptions
    • E Category Options and Descriptions
    • F Category Options and Descriptions
    • H Category Options and Descriptions
    • Pagasfsae 1
    • Page 1
  • Alarm and description of system conditions
  • Troubleshootings and Abnormalities
    • Iout 4-20/0-20mA debug process
    • OCT Alarm Debug Process
    • OCT Pulse Debug Process
    • RS485 Debug Process
  • Certification
  • FU-ES Product Page
  • LORRIC English Website
  • LORRIC Integration and Application Center
Powered by GitBook
On this page
  • Parameter Description
  • Z Quick Setup Parameter List
  • A Measure Parameter List
  • B Unit Parameter List
  • K On site Calibration Parameter List
  • C Total Parameter List
  • D Alarm & Information Parameter List
  • E Commute Parameter List
  • F Simulate Parameter List
  • H System Parameter List
Export as PDF

Parameters Table

Parameter Categorizing Table

Serial number

Name

Function

Z

Easy Setup

Z group has the most commonly used functions in other categories arranged in order to facilitate users to adjust the machine.

A

Measure

A group is about flow volume measurement

B

Unit

B group is about unit

K

Calibration

K group is ​​related to Field Calibration

C

Total

C group is about accumulated

D

Alarm & Info (Alarm & Information)

D group is about alarm and notification.

E

Commute

E group adjust OCT 4-20mA and RS485

F

Simulate

F group is about simulation mode for communication and alarm testing.

H

System

H group is for other host settings

Parameter Description

Z Quick Setup Parameter List

Serial number
Name
Function

Z01

Fully Auto Setup

Automatically execute Z02+Z03+Z04.

Z02

Auto Pipe Spec

Automatically detect pipeline specifications, and automatically jump to A02 to display the results after completion. This function is the same as A01.

Z03

Auto Initialization

Enabling this function will allow the flowmeter to adjust the signal state based on the environmental conditions. Please execute this function once every time you reinstall. This function is the same as A21.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

Z04

Auto Zero Offset

Please install the pipeline on a pipeline that is still and full inside, and activate this function to correct the zero flow error. This function is the same as A22.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

Z05

Scale Factor

Multiply the measured flow data by a fixed ratio, ranging from 0.001 to 1000. For negative flow, please go to A17 to set. This setting is synchronized with K03.

A Measure Parameter List

Serial number

Name

Function

A01

Auto Pipe Spec

Automatically detect pipeline specifications, and automatically jump to A02 to display the results after completion. This function is the same as Z02.

A02

Pipe Type

Select the line model to correct the data. Or select "Custom" to customize the pipe size and material.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A03

Pipe Geo. Unit

Pipe gauge unit, synchronized with B06.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A04

Pipe OD

Can be set when A01 is "custom". Dimensions are in accordance with B06. After adjustment, A04 and A06 will be automatically recalculated.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A05

Pipe Perimeter

Can be set when A01 is "custom". Dimensions are in accordance with B06. After adjustment, A03 and A06 will be automatically recalculated.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A06

Pipe thickness

Can be set when A01 is "custom". Dimensions are in accordance with B06. A06 will automatically recalculate after adjustment.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A07

Pipe ID

Can be set when A01 is "custom". Dimensions are in accordance with A02.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A08

Pipe Material

Set the pipe material, modify the flow data or select "Custom" to customize the sound velocity of the pipe.

(After installation is complete or if the pipeline size or material is changed, please perform Auto Initialize (Z03) and Auto Zero Offset (Z04) again to improve the accuracy of the flow meter readings and ensure product stability.)

A09

Pipe Soundspeed

When A08 is customized, you can manually set the sound velocity of the pipe, and the unit is set in B04.

A10

Liq. Type

Select the fluid type to correct the data. Or select "Custom" to customize fluid parameters.

A11

Auto Liq. Sound Speed

A12

Liq. Sound Speed

When A10 is customized, the fluid sound velocity can be manually set, and the unit is set in B04.

A13

Liq. Dyna. Viscosity

A15

Damping

A16

Direction

A17

Neg Flow (Negative Flow)

A18

Zero Cutoff

A19

Fast Update

A20

Anti-Noise

A21

Auto Initialization

A22

Auto Zero Offset

A23

Zero Offset

A24

Startup Pipe Check

B Unit Parameter List

Serial number

Name

Function

B01

Vol. Unit (Volume Unit)

Unit of instantaneous flow speed, default liter.

Metric: L, m3

B02

Time Unit

Unit of flow time seconds, minutes, hours, days. Default minutes.

B03

Total Unit (Total Volume Unit)

Unit of cumulative and history flow volume, default litre.

Metric: L, m3

B04

VelocityUnit

Unit of flow speed, default m/s.

Metric: m/s

Imperial: ft/s

B05

Dec. Place (Decimal Place)

For setting digits displayed after the decimal point on LCD and LED by using the round down method. The maximum number of digits is 4 digits.

B06

Pipe Geo. Unit

K On site Calibration Parameter List

Serial number
Name
Function

K02

Calibra. Mode

K03

Scale Factor

K04

Manual Offset

Subtract the fixed instantaneous flow rate from the input value, and the unit is the same as the system setting value. For example, inputting 1.0 means that when the original instantaneous flow is 3.0, the instantaneous flow will be output at 2.0.

C Total Parameter List

Serial number

Name

Function

C01

Total Method

Set cumulative calculation direction. There are 3 options available: forward flow, reverse flow, and net flow volume. Switching method will set the cumulative volume to zero. Default method is forward flow.

C02

Del.

Total(Delete Total)

D Alarm & Information Parameter List

Serial number

Name

Function

D01

Sensor Error Alarm.

Alarm-A0

D02

Pipe Sensor Alarm

Alarm-A1

D03

Bad UltraS. Signal

Alarm-C3

D04

Off Pipe Alarm.

Alarm-A4

Alarm when the flowmeter is not installed correctly on the pipeline.

D05

FlowLIM Ala

(Flow Volume Limit Alarm)

Alarm-B

D06

Up LIM (Upper Limit)

D07

Low LIM (Lower Limit)

D08

Hysteresis%

(Hysteresis Percentage)

Set the hysteresis percentage for the release of the flow upper and lower limit alarms

Percentages are defined as percentages of the upper and lower bounds.

The range is 0-33%, and the default value is 3%.

This parameter must be a positive value.

D09

Total Ala. (Total Alarm)

Alarm-B

D10

Total Trig. (Total Alarm Trigger Condition)

Set the notification condition of the cumulative target value (D08), greater than the target or less than the target.

D11

Total Target

D12

Iout Alarm

Alarm B

D13

Speed Alarm

Alarm B

D14

PulseOverlap

Alarm B

D15

IoutStatAla (Iout Status Alarm)

D16

Install Issue

E Commute Parameter List

Serial number

Name

Function

E01

NC/NO

E02

OCT Info

There are options below are options to define OCT output, default OFF:

OFF,

Alarm A,

Alarm A+B,

Alarm A+B+C,

flow volume alarm(adjusted by D04 D05 D06),

cumulation alarm(adjusted by D08 D09 D10),

E03

Pulse Width

If E02 selects pulse v2, set the pulse time width in this item, optional 0.5ms (millisecond), 1ms, 10ms, default 0.5 ms.

E04

Modbus ID

Set up Modbus ID location, default 1.

E05

Baud

E06

Iout Def. (Iout Definition)

E07

4mA Value

/0mA Value

E08

20mA Value

E09

Iout Error

Set up the outputted value when the flow volume is not between E07 and E08.

4 Options modes:

  1. 2.4 and 21.6 mA (When less than E07, it outputts 2.4mA. When greater than E08, it outputs 21.6mA)

  2. 2.4 mA

  3. 21.6 mA

  4. 0 or 4 & 20mA (When less than or equal to E07, it outputts 4mA or 0mA (According to E13). When greater than or equal to E08, it outputs 20mA)

E11

4mA Adj. uA (4mA Output Adjustment in microAmp)/

0mA Adj. uA (0mA Output Adjustment in microAmp)

Fine tune 0 or 4mA output value, the unit is uA.

After fine tuning and saving the setting, output current will be varied for immediate check.

E12

20mA Adj. uA (20mA Output Adjustment in microAmp)

Fine tune 20mA output value, the unit is uA.

After fine tuning and saving the setting, output current will be varied for immediate check.

E13

Iout Range

To define the output range of Analog signals, there are 2 options:

  1. 4-20mA

  2. 0-20mA

E14

PulseV2 Unit

Define how much flow volume to output a pulse, the unit is determined by B01 as follows:

  1. The unit of L and m3 is Litre.

  2. The unit of U.gal(US Gallon) and ft3 is U.gal.

E15

Byte Format

E16

Bit Order

E17

Endianness

F Simulate Parameter List

Serial number

Name

Function

F01

Sim. Volume (Simulation Volume)

F02

Sim. Mode (Simulation Mode)

Simulation function will be activated after selecting “ on ”, default off.

OCT (besides pulse), RS485 and Analog current output will be operated according to the changes of simulated data and cumulative flow.

Please be noted that cumulative flow and history data will be affected.

Simulate mode will be reminded on the screen.

H System Parameter List

Serial number

Name

Function

H01

LED Bri. (LED Brightness)

H02

LCD Bri. (LCD Brightness)

H03

Green Light

H04

Language

H06

Reset

H07

Lock Device

H08

Password

H09

Home Page

H10

Debug Page

H11

Engineering Mode

H12

System Info.

PreviousSingle Bit Data Read/Write Commands (01/05) (Commonly Used in HMIs)NextZ Category Options and Descriptions

Last updated 3 months ago

After enabling this function, the flowmeter will automatically detect the sound velocity of the fluid into the calculation. The default is off. (FW 2.0.0 released.)

When A10 is customized, the fluid dynamic viscosity can be manually set, and the unit is g/cm3.

Reduce data fluctuations, the lowest is 0, which is off, the default value is 10.

The direction of the fluid can be reversed, and the normal flow direction can be preset.

Whether to display negative flow, the default is on.

How much flow rate (absolute value) below is displayed as zero, set to 0 means off, default off.

Increased screen update rate to every 0.5 seconds. The default is off.

Eliminates unstable noise in measurement, can be turned off, and is turned on by default.

Enabling this function will allow the flowmeter to adjust the signal state based on the environmental conditions. Please execute this function once every time you reinstall. This function is the same as Z03.

Please install the pipeline on a pipeline that is still and full inside, and activate this function to correct the zero flow error. This function is synchronized with Z04.

Manually adjust or zero the Zero offset data.

After starting, there will be 5 seconds to confirm whether to use the A01 automatic regulation confirmation function. On by default.

Imperial: U.gal (US Gallon)、I.gal (Imperial Gallon), ft3

Imperial: U.gal (US Gallon)、I.gal (Imperial Gallon), ft3

The default display shows 4 digits after the decimal. Cumulative flow volume is still calculated by using the original value.

Pipe gauge unit, synchronized with A03

Select the correction scheme, currently only the simple mode.

Fine-tune flow proportionally, default 1.0. This parameter is synchronized with Z05.

The default value is 0.0. This parameter works independently of Zero Offset.

Set cumulative flow volume to 0. First select "Yes" then save.

Alarm when the ultrasonic module is abnormal. Do not disturb mode is preset.

Alarm when the module detecting pipe diameter is abnormal. Do not disturb mode is preset.

Alarm when the ultrasonic signal is poor. Do not disturb mode is preset.

Preset Do Not Disturb Mode: The red light will not flash, but the flow will return to zero when the alarm occurs, and the alarm a04 will become 1. on - When the alarm occurs, the red light will flash, the flow will return to zero, and the alarm a04 will become 1.

Set the alarm when the instantaneous flow rate exceeds the range, which can be turned off. The default is off.

Defines the upper normal range of flow for D04.

Defines the flow normal range lower limit for D04.

The alarm can be set to be turned off when the accumulated flow range is exceeded. The default is off.

The preset is larger than the target.

Set the cumulative target value.

Set whether to alarm when it exceeds the range of 4-20mA, and it can be closed. The default is off.

Set whether to alarm when the absolute value of the flow velocity exceeds the range of 6m/s, which can be turned off. On by default.

Pulse output (Pulse output) signal overlap alarm. The setting of parameter E03 is too large, resulting in overlapping of Pulse Output output signals. Can be turned off, default is on.

Set the Iout state warning mode, selectable on, off and do not disturb mode (Do not disturb), default do not disturb mode. The Do Not Disturb mode means that when an abnormality occurs, the color and LED displayed on the screen will not change, but it can still display numbers in the communication part and display abnormalities on the status page.

Alarm - C2 The signal quality is not ideal due to poor installation of the flowmeter. It is recommended to lock the flowmeter evenly to achieve the best signal quality. Default non-disturbance mode: no light, Alarm C2 displays 1.

Under normal conditions(when the oct condition does not meet). OCT should be closed(connected) or open (disconnected). The default is open.

PulseV2( adjusted by E03 and E14, please refer to the OCT output for instructions).

You can set-up Modbus communication baud rate at turning off, 9600, 19200, 38400, or 57600. Default off.

For setting output data of Analog signal, 4 options are available, off, flow rate, velocity, total. The unit is according to parameter group B. Default off.

Set up the corresponding value to 0 or 4mA, default 0. Both positive and negative values work. The value should be smaller than 20mA.

Set up the corresponding value to 20mA, default 100. Both positive and negative values work. The value should be larger than 4mA.

Default 0 or 4 & 20mA.

Positive value increases output current, negative value decreases output current.

Positive value increases output current, negative value decreases output current.

Default is 4-20mA. Modifying this item will affect the options of E09. After modifying this item, please confirm E09 meets the requirements.

The unit of I.gal(Imperial Gallon) is I.gal.

Please refer to RS485 and Modbus RTU Setting for more information. (available since FW 2.3.0)

Please refer to RS485 and Modbus RTU Setting for more information.

Please refer to RS485 and Modbus RTU Setting for more information.

Set up a simulate value of instantaneous flow speed, the unit will be the one set in parameter group B.

The corresponding communication function will work normally only after being turned on.

Set up brightness of LED with 3 levels, default middle level.

Set up brightness of LCD with 3 levels, default middle level.

Set up time of LCD green lighting with 3 durations, 10s, 60s, and always on.

Set up language. There are 3 languages: English, Traditional Chinese, Simplified Chinese, default off.

Clear all the data, reset all parameters to default values.

Turn on the password function to prevent unauthorized access to the setting screen. The password can be changed in parameter H08, default off.

Modify the 4 digits password to prevent unauthorized access to the setting screen. The password function is enabled at parameter H07. The preset password is 0000.

Set the start-up screen, the default is instantaneous flow.

Display the debugging screen, please return to the main screen after enabling it, and take a picture of the debugging screen information to the original factory to assist in debugging.

Original factory use, please do not modify it.

Display system information.

For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
Fo
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->
For more details on pipe specifications, refer to ->