Parameters Table

Parameter categorizing table

Serial number

Name

Function

Measure

A group is about flow volume measurement

Unit

B group is about unit

Total & History

C group is about accumulated and history record

Alarm & Info(Alarm & Information)

D group is about alarm and notification.

Commute

E group adjust NPN 4-20mA and RS485

Simulate

F group is about simulation mode for communication and alarm testing.

System

H group is for system parameters, like brightness and reset.

Parameter description

A Measure parameter list

Serial number

Name

Function

A01

Pipe Type

Choose correct pipe type to get correct result.

A02

Scales Factor

Fine tune flow volume in proportion, default value is 1.0.

A04

Damping

Decrease the fluctuation of data, the lowest is 0, default value is 3 seconds.

A05

Direction

Option to exchange flow direction, default normal.

B Unit parameter list

Serial number

Name

Function

B01

Vol. Unit(Volume Unit)

Unit of instantaneous flow speed,

default litre. Metric: L, m3Imperial: U.gal (US Gallon)

B02

Time Unit

Unit of flow time seconds, minutes, hours.

Default minutes.

B03

Total Unit(Total Volume Unit)

Unit of cumulative and history flow volume, default litre.Metric: L, m3Imperial: U.gal (US Gallon)

B05

Decimal Places

For setting digits displayed after the decimal point on LCDby using round down method. The maximum number of digits is 4 digits.The default display shows 4 digits after the decimal. Cumulative flow volume still calculated by using original value.

C Total & History parameter list

Serial number

Name

Function

C02

Del. Total(Delete Total)

Set cumulative flow volume to 0. First select "Yes" then save.

D Alarm & Information parameter list

Serial number

Name

Function

D01

Paddle Ala.(Paddle Alarm)

Alarm - A of paddle wheel error. Default on, but can be turned off.

D04

FlowLIM Ala (Flow Volume Limit Alarm)

Alarm - B when instantaneous flow is out of range. Default on, but can be turned off.

D05

Up LIM(Upper Limit)

Define D04 upper limit of normal flow range.

D06

Low LIM(Lower Limit)

Define D04 lower limit of normal flow range.

D07

Hysteresis% (Hysteresis Percentage)

For setting the hysteresis range of turning off alarm.The Percentage is the proportion of the range between upper and lower limit.The range is 0-33%, default 3%.This parameter needs to be positive value.

D08

Total Ala.(Total Alarm)

Alarm - B when cumulative flow is out of range. Default on, but can be turned off.

D09

Total Trig.(Total Alarm Trigger Condition)

Set-up the target cumulative value alarm condition. Option "greater than" target or "less than" target . Default "greater than" target.

D10

Total Target

Set up alarm target value of cumulative flow speed.

D13

PulseOverlap

Alarm B for Pulse Output signal overlaps caused by too long pulse width time parameter E03. Default on, but can be turned off.

(Applicable to Model FP-AS310A)

D14

IoutStatAla(Iout Status Alarm)

Set Iout status alarm mode. The options are ''on'', ''off'' and ''do not disturb.'' The default setting is ''do not disturb''. It means that when an abnormality occurs, the color displayed on the screen will not change. The number can still be displayed in the communication part, and the bit will show an abnormality on the status page.

(Applicable to Model FP-AS310A)

E Commute parameter list

Serial number

Name

Function

E01

NC/NO

Under normal conditions(when the oct condition does not meet). NPN should be closed(connected) or open (disconnected). The default is open.

(Applicable to Model FP-AS310A)

E02

OCT Info

E03

Pulse Width

(Applicable to Model FP-AS310A)

E04

Modbus ID

Set up Modbus ID location, default 1.

(Applicable to Model FP-AS310R)

E05

Baud

You can set-up Modbus communication baud rate at turnning off, 9600, 19200, 38400. Default off. (Applicable to Model FP-AS310R)

E06

Iout Def.(Iout Definition)

For setting output data of Analog signal, 4 options are available, off, flowrate, velocity, total. The unit is according to parameter group B. Default off.(Applicable to Model FP-AS310A)

E07

4mA Value

Set up corresponding value to 4mA, default 0. Both positive and negative values work. The value should be smaller than 20mA.

(Applicable to Model FP-AS310A)

E08

20mA Value

Set up corresponding value to 20mA, default 100. Both positive and negative values work. The value should be larger than 4mA.

(Applicable to Model FP-AS310A)

E11

4mA Adj. uA(4mA Output Adjustment in microAmp)

Fine tune 4mA outputted value, the unit is uA.After fine tuning and saving the setting, output current will be varied for immediate check.Positive value increases output current, negative value decreases output current.

(Applicable to Model FP-AS310A)

E12

20mA Adj. uA(20mA Output Adjustment in microAmp)

Fine tune 20mA outputted value, the unit is uA.After fine tuning and saving the setting, ooutput current will be varied for immediate check.Positive value increases output current, negative value decreasess output current. (Applicable to Model FP-AS310A)

E14

PulseV2 Unit

Define how much flow volume to output a pulse, the unit is determined by B01 as follows：

The unit of L and m3 is Litre.
The unit of U.gal(US Gallon) and ft3 is U.gal.
The unit of I.gal(Imperial Gallon) is I.gal.

(Applicable to Model FP-AS310A)

E15

Byte format

(Applicable to Model FP-AS310R)

E16

Bit order

(Applicable to Model FP-AS310R)

E17

Endianness

(Applicable to Model FP-AS310R)

F Simulate parameter list

Serial number

Name

Function

F01

Sim. Volume (Simulation Volume)

Set up simulate value of instantaneous flow speed, the unit will be the one set in parameter group B.

F02

Sim. Mode (Simulation Mode)

Simulation function will be activated after selecting “ on ”, default off. NPN(besides pulse), RS485 and Analog current output will be operated according to the changes of simulated data and cumulative flow.Please be noted that cumulative flow and history data will be affected.Simulate mode will be reminded on the screen.The corresponding communication function will work normally only after being turned on.

F03

Sim. PulseHz (Simulation PulseHz)

Under this page, pulse signal will be outputted according to set frequency within value 0 to 700. Please set up NC/NO of pulse according to parameter E01, and pulse width according to parameter E03. It operates whether NPN info is turned on or not.

(Applicable to Model FP-AS310A))

H System parameter list

Serial number

Name

Function

H02

LCD Bri.(LCD Brightness)

Set up brightness of LCD with 3 levels, default middle level.

H03

Green Light

Set up time of LCD green lighting with 3 durations, 10s, 60s, and always on.

H04

Language

Set up language. There are 2 languages:English, Traditional Chinese, default off.

H05

Paddle Init.(Paddle Initialization)

Press "Start" to initialize the paddle. User needs to rotate the paddle at least 20 rounds until the screen shows "Init. Succeed". If screens shows "Init. Failed", please try again. If the problem persists, please replace your paddle.

H06

Reset

Clear all the data (include date and cumulative data), reset all parameters to default values.

H07

Lock Device

Turn on the password function to prevent unauthorized access to the setting screen. The password can be changed in parameter H08, default off.

H08

Password

Modify the 4 digits password to prevent unauthorized access to the setting screen. The password function is enabled at parameter H07. The preset password is 0000.

H09

Engineer mode

H10

System Info

H11

Home Page

PreviousSingle Bit 資料讀寫指令(01/05)(人機介面常用)NextA 分類選項及說明

Last updated 18 days ago

Parameter description

A Measure parameter list

Serial number

Name

Function

A01

Pipe Type

Choose correct pipe type to get correct result.

A02

Scales Factor

Fine tune flow volume in proportion, default value is 1.0.

A04

Damping

Decrease the fluctuation of data, the lowest is 0, default value is 3 seconds.

A05

Direction

Option to exchange flow direction, default normal.

B Unit parameter list

Serial number

Name

Function

B01

Vol. Unit(Volume Unit)

Unit of instantaneous flow speed,

default litre. Metric: L, m3Imperial: U.gal (US Gallon)

B02

Time Unit

Unit of flow time seconds, minutes, hours.

Default minutes.

B03

Total Unit(Total Volume Unit)

Unit of cumulative and history flow volume, default litre.Metric: L, m3Imperial: U.gal (US Gallon)

B05

Decimal Places

C Total & History parameter list

Serial number

Name

Function

C02

Del. Total(Delete Total)

Set cumulative flow volume to 0. First select "Yes" then save.

D Alarm & Information parameter list

Serial number

Name

Function

D01

Paddle Ala.(Paddle Alarm)

Alarm - A of paddle wheel error. Default on, but can be turned off.

D04

FlowLIM Ala (Flow Volume Limit Alarm)

Alarm - B when instantaneous flow is out of range. Default on, but can be turned off.

D05

Up LIM(Upper Limit)

Define D04 upper limit of normal flow range.

D06

Low LIM(Lower Limit)

Define D04 lower limit of normal flow range.

D07

Hysteresis% (Hysteresis Percentage)

D08

Total Ala.(Total Alarm)

Alarm - B when cumulative flow is out of range. Default on, but can be turned off.

D09

Total Trig.(Total Alarm Trigger Condition)

Set-up the target cumulative value alarm condition. Option "greater than" target or "less than" target . Default "greater than" target.

D10

Total Target

Set up alarm target value of cumulative flow speed.

D13

PulseOverlap

Alarm B for Pulse Output signal overlaps caused by too long pulse width time parameter E03. Default on, but can be turned off.

(Applicable to Model FP-AS310A)

D14

IoutStatAla(Iout Status Alarm)

(Applicable to Model FP-AS310A)

E Commute parameter list

Serial number

Name

Function

E01

NC/NO

Under normal conditions(when the oct condition does not meet). NPN should be closed(connected) or open (disconnected). The default is open.

(Applicable to Model FP-AS310A)

E02

OCT Info

There are options below are options to define NPN output, default OFF:OFF,Alarm A,Alarm A+B,Alarm A+B+C,flow volume alarm(adjusted by D04 D05 D06),cumulation alarm(adjusted by D08 D09 D10),paddle wheel pulse output( adjusted by E03, please refer to the for instructions).PulseV2( adjusted by E03 and E14, please refer to the for instructions). (Applicable to Model FP-AS310A)

E03

Pulse Width

If paddlewheel pulse is selected in E02, you set the pulse width to 0.5 ms (millisecond), 1ms, or 10ms. The default is 0.5ms. Every 180° paddlewheel rotation will output a pulse. Please refer to the for flow volume calculation.

(Applicable to Model FP-AS310A)

E04

Modbus ID

Set up Modbus ID location, default 1.

(Applicable to Model FP-AS310R)

E05

Baud

You can set-up Modbus communication baud rate at turnning off, 9600, 19200, 38400. Default off. (Applicable to Model FP-AS310R)

E06

Iout Def.(Iout Definition)

For setting output data of Analog signal, 4 options are available, off, flowrate, velocity, total. The unit is according to parameter group B. Default off.(Applicable to Model FP-AS310A)

E07

4mA Value

Set up corresponding value to 4mA, default 0. Both positive and negative values work. The value should be smaller than 20mA.

(Applicable to Model FP-AS310A)

E08

20mA Value

Set up corresponding value to 20mA, default 100. Both positive and negative values work. The value should be larger than 4mA.

(Applicable to Model FP-AS310A)

E11

4mA Adj. uA(4mA Output Adjustment in microAmp)

(Applicable to Model FP-AS310A)

E12

20mA Adj. uA(20mA Output Adjustment in microAmp)

E14

PulseV2 Unit

Define how much flow volume to output a pulse, the unit is determined by B01 as follows：

The unit of L and m3 is Litre.
The unit of U.gal(US Gallon) and ft3 is U.gal.
The unit of I.gal(Imperial Gallon) is I.gal.

(Applicable to Model FP-AS310A)

E15

Byte format

Please refer to for more information.

(Applicable to Model FP-AS310R)

E16

Bit order

Please refer to for more information.

(Applicable to Model FP-AS310R)

E17

Endianness

Please refer to for more information.

(Applicable to Model FP-AS310R)

F Simulate parameter list

Serial number

Name

Function

F01

Sim. Volume (Simulation Volume)

Set up simulate value of instantaneous flow speed, the unit will be the one set in parameter group B.

F02

Sim. Mode (Simulation Mode)

F03

Sim. PulseHz (Simulation PulseHz)

(Applicable to Model FP-AS310A))

H System parameter list

Serial number

Name

Function

H02

LCD Bri.(LCD Brightness)

Set up brightness of LCD with 3 levels, default middle level.

H03

Green Light

Set up time of LCD green lighting with 3 durations, 10s, 60s, and always on.

H04

Language

Set up language. There are 2 languages:English, Traditional Chinese, default off.

H05

Paddle Init.(Paddle Initialization)

H06

Reset

Clear all the data (include date and cumulative data), reset all parameters to default values.

H07

Lock Device

Turn on the password function to prevent unauthorized access to the setting screen. The password can be changed in parameter H08, default off.

H08

Password

Modify the 4 digits password to prevent unauthorized access to the setting screen. The password function is enabled at parameter H07. The preset password is 0000.

H09

Engineer mode

H10

System Info

H11

Home Page