LORRIC Docs For Partners
FU-TX 310 Clamp-on Ultrasonic Flowmeter Manual v2.
FU-TX 310 Clamp-on Ultrasonic Flowmeter Manual v2.
  • This instruction manual version is v2.1
  • 1. Product Introduction
    • 1.1 Specifications
    • 1.2 Important concepts
    • 1.3 Product features
    • 1.4 Product applications
    • 1.5 Measuring principle
    • 1.6 Product contents
    • 1.7 User interface
      • 1.7.1 Screen interfaces
      • 1.7.2 Buttons
      • 1.7.3 LED message
  • 2. Installation Method
    • 2.1 Power
    • 2.2 Ultrasonic probe
      • 2.2.1 Probe wiring
      • 2.2.2 Meter wiring
      • 2.2.3 Installation location
      • 2.2.4 Installation method
      • 2.2.5 ​Probe installation method
    • 2.3 Temperature sensor/Analog output
      • 2.3.1 Temperature sensor
      • 2.3.2 Analog output
      • 2.3.3 Wiring method
    • 2.4 Installation check
      • 2.4.1 RSSI (Signal Strength)
      • 2.4.2 Q value
      • 2.4.3 Flight time
  • 3. Output Interface
  • 4. Setting up the Interface
    • 4.1 Intial menu settings
    • 4.2 Units
    • 4.3 Meter (Measurement Settings)
    • 4.4 Communication
    • 4.5 Other
    • 4.6 Save
  • 5. Error Messages and Solutions
  • 6. Other Conditions
  • 7. MODBUS Communication Protocol
  • 8. Cautions
  • 9. Sound Speeds Data
  • LORRIC Integration and Application Center
Powered by GitBook
On this page
  1. 4. Setting up the Interface

4.2 Units

Measurement Unit

Metric or Imperial units

Flow Numerator

  1. m³ (Cubic meter)

  2. L (Liter) = 10-3 * m³

  3. gal (US gallons) = 3.785412 * 10-3 m³

  4. igl (Imperial gallons) = 4.54609 * 10-3 m³

  5. mgl (million US gallons) = 3785412 * 10-3 m³

  6. cf (Cubic feet) = 28.3164847 * 10-3 m³

  7. bal (US liquid barrel) = 35.23907 * 10-3m³

  8. ob (Oil barrel) = 158.987295 * 10-3m³

Flow Denominator

  1. sec (seconds)

  2. min (minutes)

  3. hr (hours)

  4. day (days)

Totalizer Units

Same as flow denominator (volume) units

Totalizer Decimal

Up to 7 digits can be set; decimal point position can be changed.

Enable NET Total

Turns net cumulative flow on or off (note that cumulative flow automatically zeroes at > 4,000,000,000,000 m3 ).

Enable POS Total

Turns positive cumulative flow on or off (cumulative flow automatically zeroes at > 4,000,000,000,000 m3 ).

Enable NEG Total

Turns negative accumulated flow on or off (accumulated flow automatically zeroes at > 4,000,000,000,000 m3 )

Reset Totalizer

Can be zero net, positive, or negative cumulative flow, or all zero at the same time.

Temperature Unit

Set temperature units:

1. °C (degrees Celsius)

2. °F (degrees Fahrenheit)

Previous4.1 Intial menu settingsNext4.3 Meter (Measurement Settings)

Last updated 4 years ago